Search results for "Fault detection"
showing 10 items of 77 documents
Early detection and classification of bearing faults using support vector machine algorithm
2017
Bearings are one of the most critical elements in rotating machinery systems. Bearing faults are the main reason for failures in electrical motors and generators. Therefore, early bearing fault detection is very important to prevent critical system failures in the industry. In this paper, the support vector machine algorithm is used for early detection and classification of bearing faults. Both time and frequency domain features are used for training the support vector machine learning algorithm. The trained classier can be employed for real-time bearing fault detection and classification. By using the proposed method, the bearing faults can be detected at early stages, and the machine oper…
Multi-Component Fault Detection in Wind Turbine Pitch Systems Using Extended Park's Vector and Deep Autoencoder Feature Learning
2018
Pitch systems are among the wind turbine components with most frequent failures. This article presents a multicomponent fault detection for induction motors and planetary gearboxes of the electric pitch drives using only the three-phase motor line currents. A deep autoencoder is used to extract features from the extended Park's vector modulus of the motor three-phase currents and a support vector machine to classify faults. The methodology is validated in a laboratory setup of a scaled pitch drive, with four commonly occurring faults, namely, the motor stator turns fault, broken rotor bars fault, planetary gearbox bearing fault and planet gear faults, under varying load and speed conditions.
Cross-correlation of whitened vibration signals for low-speed bearing diagnostics
2019
Abstract Rolling-element bearings are crucial components in all rotating machinery, and their failure will initially degrade the machine performance, and later cause complete shutdown. The period between an initial crack and complete failure is short due to crack propagation. Therefore, early fault detection is important to avoid unexpected machine shutdown and to aid in maintenance scheduling. Bearing condition monitoring has been applied for several decades to detect incipient faults at an early stage. However, low-speed conditions pose a challenge for bearing fault diagnosis due to low fault impact energy. To reliably detect bearing faults at an early stage, a new method termed Whitened …
Health Indicator for Low-Speed Axial Bearings Using Variational Autoencoders
2020
This paper proposes a method for calculating a health indicator (HI) for low-speed axial rolling element bearing (REB) health assessment by utilizing the latent representation obtained by variational inference using Variational Autoencoders (VAEs), trained on each speed reference in the dataset. Further, versatility is added by conditioning on the speed, extending the VAE to a conditional VAE (CVAE), thereby incorporating all speeds in a single model. Within the framework, the coefficients of autoregressive (AR) models are used as features. The dimensionality reduction inherent in the proposed method lowers the need of expert knowledge to design good condition indicators. Moreover, the sugg…
Fault detection for nonlinear networked systems based on quantization and dropout compensation: An interval type-2 fuzzy-model method
2016
Abstract This paper investigates the problem of filter-based fault detection for a class of nonlinear networked systems subject to parameter uncertainties in the framework of the interval type-2 (IT2) T–S fuzzy model-based approach. The Bernoulli random distribution process and logarithm quantizer are used to describe the measurement loss and signals quantization, respectively. In the framework of the IT2 T–S fuzzy model, the parameter uncertainty is handled by the membership functions with lower and upper bounds. A novel IT2 fault detection filter is designed to guarantee the residual system to be stochastically stable and satisfy the predefined H ∞ performance. It should be mentioned that…
Multi-band identification for enhancing bearing fault detection in variable speed conditions
2020
Abstract Rolling element bearings are crucial components in rotating machinery, and avoiding unexpected breakdowns using fault detection methods is an increased demand in industry today. Variable speed conditions render a challenge for vibration-based fault diagnosis due to the non-stationary impact frequency. Computed order tracking transforms the vibration signal from time domain to the shaft-angle domain, allowing order analysis with the envelope spectrum. To enhance fault detection, the bearing resonance frequency region is isolated in the raw signal prior to order tracking. Identification of this region is not trivial but may be estimated using kurtosis-based methods reported in the li…
Food tray sealing fault detection using hyperspectral imaging and PCANet
2020
Abstract Food trays are very common in shops and supermarkets. Fresh food packaged in trays must be correctly sealed to protect the internal atmosphere and avoid contamination or deterioration. Due to the speed of production, it is not possible to have human quality inspection. Thus, automatic fault detection is a must to reach high production volume. This work describes a deep neural network based on Principal Component Analysis Network (PCANet) for food tray sealing fault detection. The input data come from hyperspectral cameras, showing more characteristics than regular industrial cameras or the human eye as they capture the spectral properties for each pixel. The proposed classification…
Characterization of DC series arc faults in PV systems based on current low frequency spectral analysis
2021
Abstract This work presents an experimental study focused on the characterization of series arc faults in direct current (DC) photovoltaic (PV) systems. The aim of the study is to identify some relevant characteristics of arcing current, which can be obtained by means of low frequency spectral analysis of current signal. On field tests have been carried out on a real PV system, in accordance with some tests requirements of UL 1699B Standard for protection devices against PV DC arc faults. Arcing and non-arcing current signals are acquired and compared and the behavior of a set of indicators proposed by authors is analyzed. Different measurement equipment have been used, in order to study th…
Fault detection for continuous-time switched systems under asynchronous switching
2013
In this chapter, the problem of FD for continuous-time switched systems under asynchronous switching is investigated. The designed FD filter is assumed to be asynchronous with the original systems. Attention is focused on designing a FD filter such that the estimation error between the residual and the fault is minimized in the sense of H ∞ norm. By employing piecewise Lyapunov function and ADT techniques, a sufficient condition for the existence of such a filter is exploited in terms of certain LMIs. Finally, an example is provided to illustrate the effectiveness of the proposed approach.
Statistics-driven Development of OBD Systems: An Overview
2006
Automotive on-board diagnostic (OBD) systems are designed to keep critical components under control during vehicle functioning, and to alert the driver in case of severe malfunctions. OBD systems aimed at reducing polluting emissions are mandatory on new motor vehicles. Some research projects conducted in cooperation between universities and the automotive industry have been quite successful in terms of knowledge advancement and industrial gain. An updated overview of the adopted methodologies and results obtained are given in this article. Such results can be valuable for both theorists and practitioners, since they witness the use of statistics as a powerful catalyst of technical progress…